Aerial Rooftop Inspections

Welcome to the Knowledge Assessment for the Airware Aerial Rooftop Inspection training program.

Answer all of the questions to the best of your ability, and then click the Submit All Answers button at the bottom of the page.

Knowledge Assessment

What are the three phases of the Airware workflow?

  • Land
  • Fly
  • Analyze
  • Launch
  • Plan
  • Monitor

The minimum vertical distance above an obstacle around your flight plan is ________.

  • 5 meters
  • 10 meters
  • 15 meters
  • 20 meters

The maximum wind limit for flight operations is _______.

  • 10 knots
  • 20 knots
  • 30 knots
  • 40 knots

You create jobs for aerial rooftop inspections in the Airware Cloud.

  • True
  • False

When you ______ a job in the Ground Control Station, all the job information, including the location, geofence, and flight plan, are saved on your computer for working in offline mode.

  • save
  • cache
  • open
  • pin

The average flight time that the aircraft can sustain is between _________.

  • 7 and 14 minutes
  • 10 and 14 minutes
  • 10 and 20 minutes
  • 15 and 20 minutes

As long as the job has been approved by Airware, there is no need to check airspace or GPS coverage the day of the job.

  • True
  • False

Photo Survey image files are transferred from the aircraft to the GCS using __________.

  • a USB cable
  • Wi-Fi
  • Bluetooth
  • SD card

The second waypoint of the Point Photo Survey is where you choose the __________.

  • launch point
  • survey points
  • land point

The aircraft will not recognize the new camera if you do not restart the Airware Connect app after installing a different gimbal.

  • True
  • False

If you receive a Low Voltage alert, you should ______________.

  • immediately press Return Home
  • let the aircraft finish the flight plan
  • immediately press Land Now

____________ every flight.

  • Verify aircraft battery charge is at least 20% before
  • Verify aircraft battery charge is at least 50% before
  • Verify aircraft battery charge is at least 80% before
  • Install a fully charged aircraft battery before

The Internet upload speed at the job site must be at least _______.

  • 1 Mbps
  • 1.5 Mbps
  • 2 Mbps
  • 3 mbps

What is the make and model of the aircraft in the aerial inspection kit?

  • Airware Inspire Pro 1
  • DJI Phantom
  • DJI Inspire
  • DJI Inspire Pro 1 Pro T600

What are the three things to check prior to arriving on site?

  • Obstacles
  • TFRs
  • Height of Roof
  • Weather
  • NOTAMs

To power on and off the aircraft, press the power button once and hold.

  • True
  • False

The required cloud ceiling is ______.

  • 400 feet
  • 1000 feet
  • 1 mile
  • 3 miles

When creating a job in the Airware Cloud, you can edit the __________ for the first flight, the Photo Survey.

  • camera settings
  • No-Fly Zone
  • flight plan
  • survey points

Which two Photo Survey waypoints define the flight plans?

  • Waypoint 1
  • Waypoint 2
  • Waypoint 3
  • Waypoint 4

A _________ represents the boundaries for the flight path of the aircraft.

  • No-Fly Zone
  • vertical offset
  • geofence

Where do you download the Measurement Report?

  • Cloud Data page
  • GCS
  • Fleet Manager
  • e-mail message

Safe operating temperatures for the aircraft are between _______.

  • 10-100° F
  • 0-120° F
  • 14-104° F
  • 20-120° F

For Photo Surveys, the Launch and Land waypoints should be positioned outside of the flight plan survey areas.

  • True
  • False

What two applications allow you to create image annotations?

  • Cloud
  • SkyVector
  • Fleet Manager
  • Ground Control Station

The most common site survey showstopper is _______.

  • an inadequate launch/landing location
  • overhanging trees
  • power lines
  • cell towers

How many waypoints are required for a Photo Survey?

  • two
  • three
  • four
  • five

While __________, do not close the Analyze page.

  • generating the report
  • syncing with the Cloud
  • generating the map layer
  • planning a flight

If you encounter an airspace conflict, you should either Return Home or Land Now, depending on the proximity of the encroaching aircraft.

  • True
  • False

To expedite access to the Rooftop CAD Model, filter the Airware Cloud Data page for the job by ______.

  • Rooftop CAD Model
  • DXF
  • point cloud
  • 3D

The lateral distance from obstacles required for a launch and landing location is _______.

  • 3 meters
  • 5 meters
  • 10 meters
  • 20 meters

The required visibility for operating the aircraft is _______.

  • 1000 feet
  • 1 mile
  • 3 miles
  • 10 miles

The lowest acceptable voltage for operating non-aircraft batteries is ____.

  • 20%
  • 50%
  • 60%
  • 80%

A _________ collects optical images of the area to create an Orthomosaic and a point cloud.

  • Photo Survey
  • Point Photo Survey

Once processed, you download the Rooftop CAD Model from the __________.

  • Ground Control Station
  • Fleet Manager
  • e-mail message
  • Cloud Data page

Flight operations may not proceed in rain but are permitted in light fog.

  • True
  • False

Measure the highest point of the house to set the ________ for the flight plan.

  • GSD
  • maximum altitude
  • vertical offset
  • focal point

You must edit the auto-generated Photo Survey flight plans to adjust the _______________.

  • survey areas
  • image resolution
  • vertical offsets
  • flight time
  • GSDs

Once the Photo Survey flight plan has been saved, you must upload and activate the flight plan before you can fly the aircraft.

  • True
  • False

The __________ button creates a preview orthomosaic in the GCS for planning the Point Photo Survey.

  • Generate Map Layers
  • Generate Report
  • Upload
  • Import

You should upload the Point Photo Survey images to the Cloud _________.

  • immediately after the flight
  • prior to leaving the job site
  • when you return to the office

To resolve ground conflicts during flight operations, press the Pause button.

  • True
  • False

To adjust for the height measured for the tallest obstacle during the site survey, the _____ must be changed in the Photo Survey flight plan.

  • vertical offset
  • maximum altitude
  • GSD
  • focal point

Sensor 1 is used for the Point Photo Survey, while Sensor two is used for the Photo Survey.

  • True
  • False

Annotations added to image files in the GCS _______________.

  • can only be viewed locally
  • will be displayed in the Airware Cloud once the job is synced
  • will be displayed in the Airware Cloud immediately

If you encounter a ground conflict while the aircraft is executing a flight plan, you should press the Pause button and then resolve the ground conflict.

  • True
  • False

The flight plan for the initial Photo Survey is auto-generated in the Airware Cloud.

  • True
  • False

The __________ button uploads the Photo Survey images to the Cloud to generate the Orthomosaic, Rooftop CAD Model, and Measurement Report.

  • Upload
  • Generate Map Layers
  • Import
  • Generate Report

Point Photo Survey flight plans are auto-generated in the Airware Cloud.

  • True
  • False

When the aircraft detects a diminished GPS signal, the aircraft will ___________.

  • Land Now
  • Return Home
  • Pause
  • continue the flight plan

After transferring image files from the aircraft to the GCS and importing them, you should delete the image files from the aircraft SD card.

  • True
  • False